Greetings everyone.
Havnt been on here for awhile. Good to see there is still so much knowledge being shared here.
I have a question I hoping someone knows or has pics of.
Looking for the difference in measurements for early lh lx strait pushrod to booster. Then later lx uc that Had bent push rod to booster. And auto pedal if there was a difference.
Brake pedal differences lx lh uc. Auto. manual
Started by
_76lxJAS_
, Jan 12 2021 10:40 PM
8 replies to this topic
#2
BIG KEV
-
- Members
-
- 1,202 posts
Forum Fixture
- Name:Kevin
- Location:SYDNEY
- Car:LHSLR5000 and The 6LT Project
- Joined: 02-January 12
Posted 13 January 2021 - 05:36 PM
I have just been through this
The answer to your question is the bent pushrod booster hole is 9mm lower the the straight one
i hope that makes sense
i have both here
Cheers Kevin
#3
_76lxJAS_
_76lxJAS_
-
- Guests
Posted 13 January 2021 - 07:19 PM
Can you give me a reference point to measure this from please?
I only have the one and trying to confirm what booster should be in it.
I only have the one and trying to confirm what booster should be in it.
#4
UCSLE
-
- Members
-
- 702 posts
Forum Fixture
- Name:troy
- Location:perth
- Car:Goggomobil
- Joined: 23-June 09
Posted 14 January 2021 - 01:50 AM
The pedals i have the stop light tab thing is welded to the front of the pedal for the straight rod booster
The pedal for the bent rod booster has it welded on the side
dont know if they are all like that but could be a way of telling them apart ?
bp.JPG 35.86K
9 downloads
#5
BIG KEV
-
- Members
-
- 1,202 posts
Forum Fixture
- Name:Kevin
- Location:SYDNEY
- Car:LHSLR5000 and The 6LT Project
- Joined: 02-January 12
Posted 14 January 2021 - 04:59 PM
Yes that is correct
You need to weld up the old hole and redrill 9mm lower
Centre to centre of hole
The pedal in the above post on right is for a bent rod booster
Edited by BIG KEV, 14 January 2021 - 05:07 PM.
#6
_76lxJAS_
_76lxJAS_
-
- Guests
Posted 14 January 2021 - 09:44 PM
Can you tell me the measuments from the center of bolt hole to center of pins please
#7
Toranamat69
-
- Members
-
- 2,117 posts
Forum R&D Officer
- Location:Brisbane
- Joined: 07-November 05
Posted 14 January 2021 - 10:17 PM
I only have bent pushrod type here and I measure the manual one at 73mm from pivot bolt centre to pin centre.
The auto pedal I got from Ebay looks to be h series Holden now I look closely but the torana auto pedal would need to be the same pin position or it wouldn't line up.
The auto pedal I got from Ebay looks to be h series Holden now I look closely but the torana auto pedal would need to be the same pin position or it wouldn't line up.
#8
Toranamat69
-
- Members
-
- 2,117 posts
Forum R&D Officer
- Location:Brisbane
- Joined: 07-November 05
Posted 14 January 2021 - 10:35 PM
Here's and old thread.
http://www.gmh-toran...tios-for-lh-lx/
Looks like I got 71mm not 73 back then.
I'll go check again.
http://www.gmh-toran...tios-for-lh-lx/
Looks like I got 71mm not 73 back then.
I'll go check again.
#9
Toranamat69
-
- Members
-
- 2,117 posts
Forum R&D Officer
- Location:Brisbane
- Joined: 07-November 05
Posted 14 January 2021 - 10:48 PM
Bit tricky to measure accurately as the old bushes have a bit of play. I'd actually say 72mm after checking again.
If you need more accurate, I'll have to remove the bolt and bushes and measure inside diameters etc and calculate the actual distance.
If you need more accurate, I'll have to remove the bolt and bushes and measure inside diameters etc and calculate the actual distance.
Edited by Toranamat69, 14 January 2021 - 10:52 PM.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users
