Jump to content


Photo

Suspension Bushes

Bushes suspension

  • Please log in to reply
11 replies to this topic

#1 dacastle

dacastle

    Forum Member

  • Members
  • PipPipPip
  • 74 posts
  • Name:Dave
  • Location:Adelaide
  • Car:LC gtr
  • Joined: 22-March 21

Posted 12 June 2022 - 02:17 PM

I had a new set of suspension bushes from restocounrty spares pressed into the rear suspension components

 

Has anyone had the issue where the bolts now wont fit into the new bushes

 

Is the solution simply to drill out new bushes with slightly larger drill bit ?

 

Thanks for any suggestions

 

 

 

 

 

Attached Files



#2 sibhs

sibhs

    Lotsa Posts!

  • Members
  • PipPipPipPipPipPip
  • 2,699 posts
  • Name:Martin
  • Location:Perth
  • Car:LJ Coupe S
  • Joined: 27-July 12

Posted 12 June 2022 - 07:21 PM

I checked the bolts on mine and they wouldn't fit before pressing them in. I was advised to drill them out which was easy and all good so far.  Half inch drill bit was spot on.

 

Marty


Edited by sibhs, 12 June 2022 - 07:24 PM.


#3 Indy Orange

Indy Orange

    Lotsa Posts!

  • Members
  • PipPipPipPipPipPip
  • 2,840 posts
  • Name:Paul
  • Location:Australia
  • Joined: 03-July 09

Posted 12 June 2022 - 07:32 PM

That’s strange! I purchased the Mackay ones ,I would have thought those Kingswood Country ones would have been the same.



#4 dacastle

dacastle

    Forum Member

  • Members
  • PipPipPip
  • 74 posts
  • Name:Dave
  • Location:Adelaide
  • Car:LC gtr
  • Joined: 22-March 21

Posted 13 June 2022 - 10:07 AM

I checked the bolts on mine and they wouldn't fit before pressing them in. I was advised to drill them out which was easy and all good so far.  Half inch drill bit was spot on.

 

Marty

Thanks Marty - will do - I didnt try them before they were pressed in



#5 dacastle

dacastle

    Forum Member

  • Members
  • PipPipPip
  • 74 posts
  • Name:Dave
  • Location:Adelaide
  • Car:LC gtr
  • Joined: 22-March 21

Posted 13 June 2022 - 10:12 AM

That’s strange! I purchased the Mackay ones ,I would have thought those Kingswood Country ones would have been the same.

 

Yes I have tried all the rear suspension bolts and nearly all the bushes that been pressed in wont allow the bolts to go in .

 

I didnt hammer them in as I didnt want to damage the threads 



#6 Heath

Heath

    I like cars.

  • Administrators
  • PipPipPipPipPipPipPip
  • 18,299 posts
  • Name:Heath
  • Location:Eastern Suburbs, Melbourne
  • Car:Heavily Modified UC Sunbird Hatchback
  • Joined: 07-November 05
Garage View Garage

Posted 14 June 2022 - 09:54 AM

That is pretty shithouse if they are undersized.

 

I would just make sure it isn't a burr on the edge (countersinking tool should clean it up in 1 second) and if it's still tight, then yeah, drill it out to 1/2" as the others have said.

Pressing them in shouldn't have made any difference to the I.D. of that tube. It would have been too tight even before you installed them I imagin, if they're tight now.

 

Make sure you coat those bolts in a thin layer of copper anti-seize before insertion, particularly as you'll be losing any zinc coating that's on the crush-tubes by drilling them out.



#7 dacastle

dacastle

    Forum Member

  • Members
  • PipPipPip
  • 74 posts
  • Name:Dave
  • Location:Adelaide
  • Car:LC gtr
  • Joined: 22-March 21

Posted 16 June 2022 - 01:54 PM

That is pretty shithouse if they are undersized.

 

I would just make sure it isn't a burr on the edge (countersinking tool should clean it up in 1 second) and if it's still tight, then yeah, drill it out to 1/2" as the others have said.

Pressing them in shouldn't have made any difference to the I.D. of that tube. It would have been too tight even before you installed them I imagin, if they're tight now.

 

Make sure you coat those bolts in a thin layer of copper anti-seize before insertion, particularly as you'll be losing any zinc coating that's on the crush-tubes by drilling them out.

They re definetely undersize - ran a 1/2 inch drill through and shaved off a small amount of metal all the way through on every bush



#8 Heath

Heath

    I like cars.

  • Administrators
  • PipPipPipPipPipPipPip
  • 18,299 posts
  • Name:Heath
  • Location:Eastern Suburbs, Melbourne
  • Car:Heavily Modified UC Sunbird Hatchback
  • Joined: 07-November 05
Garage View Garage

Posted 17 June 2022 - 09:57 AM

Yep. I feel that I may have actually encountered this problem with some bushes myself at one point as well.

 

Lousy, but easily overcome. Good stuff mate.



#9 Rockoz

Rockoz

    Lotsa Posts!

  • Members
  • PipPipPipPipPipPip
  • 3,955 posts
  • Name:Rob
  • Location:Cowra NSW
  • Joined: 21-September 08

Posted 17 June 2022 - 11:17 AM

Probably because you cant buy imperial sized tube any more.

But you would think the manufacturer of the product would make them fit for purpose by drilling them out before being packaged and sold.

 

Cheers

 

Rob



#10 S pack

S pack

    Scrivet Counter

  • Members
  • PipPipPipPipPipPipPip
  • 15,522 posts
  • Name:Dave
  • Location:Luggage Point
  • Car:73 LJ
  • Joined: 25-January 10

Posted 17 June 2022 - 03:59 PM

The inner sleeves in those bushes are rolled from a piece of flat sheet so they should be made to suit.

#11 rodomo

rodomo

    To advertise here, call 13TORANA

  • Members
  • PipPipPipPipPipPipPip
  • 17,997 posts
  • Name:R - O - B Dammit!
  • Location:Way out west of Melbourne Awstraylya
  • Joined: 10-December 05

Posted 17 June 2022 - 10:48 PM

To be honest? I'd be happy with a bit of tappy tappy knock knock interference fit.



#12 sibhs

sibhs

    Lotsa Posts!

  • Members
  • PipPipPipPipPipPip
  • 2,699 posts
  • Name:Martin
  • Location:Perth
  • Car:LJ Coupe S
  • Joined: 27-July 12

Posted 28 June 2022 - 08:27 AM

Just thought I'd post up my Holden bush as a reference. Notice it a full tube.

 

Attached File  IMG_8853.jpeg   126.79K   8 downloads

 

I've also seen Mackay Bushes with rolled flat bar tube and with a tube.

 

Marty







Also tagged with one or more of these keywords: Bushes, suspension

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users