LC - Original Speaker mounting
#1 _CraigA_
Posted 02 August 2007 - 03:52 PM
I've sourced an original radio/speaker/aerial complete for my XU1 and want to confirm speaker location. I know its under the glovebox area, but need to know how it is fixed in place.
Many Thanks,
Craig.
#3
Posted 03 August 2007 - 06:30 AM
Edited by LC69GTR, 03 August 2007 - 06:32 AM.
#4 _CraigA_
Posted 03 August 2007 - 08:52 AM
EXACTLY what I was looking for
Cheers,
Craig.
#5 _CraigA_
Posted 05 August 2007 - 08:37 PM
Thanks again, factory documents made it all easy.
#6
Posted 06 August 2007 - 11:40 AM
#7 _CraigA_
Posted 06 August 2007 - 12:34 PM
Yes, the two side brackets came with the radio, as did the speaker and aerial. The bit that was missing was the upper speaker bracket, with the factory diagrams I can now make one and fit it up correctly. It is also missing the rear mount for the radio, as you can see in the diagrams its only a piece of flat light gauge steel and I would guess typical of the type used in many car radio installations. Should be able to source it from Jaycar.
Cheers,
Craig.
#8
Posted 06 August 2007 - 01:59 PM
#9 _CraigA_
Posted 06 August 2007 - 02:35 PM
This panel relies on the speaker being fixed with the mount that's missing though, and I will fit it all when I've made the bracket and then post full pics in this thread as a reference for others.
I held it up there a million times trying to work out how the panel was secured - the front was easy, but for the life of me I couldn't suss out the rear mount. When these diagrams were posted the riddle was solved.
#10
Posted 06 August 2007 - 03:02 PM
#11 _CraigA_
Posted 06 August 2007 - 03:30 PM
Here's the bracket extracted and enlarged.
Would need these three if you don't mind.
#12
Posted 06 August 2007 - 03:50 PM
You will also need the measurement of the right hand vertical (in the picture) as it is a different length to the other one. The longest one goes nearest the firewall.
Bazza
#13 _CraigA_
Posted 06 August 2007 - 04:10 PM
#14
Posted 06 August 2007 - 04:17 PM
#15
Posted 06 August 2007 - 10:23 PM
#16
Posted 04 September 2007 - 04:04 PM
Craig, by your diagram, the horizontal blue measurement is 185mm, the horizontal red measuremnt is 155mm, the longer vertical arm is 75mm and the shorter vertical arm is 65mm.
Also, the bracket is 25mm wide, and mine is non passivated zinc plated (silver) rather that the passivated plated gold colour that Bazza posted.
Cheers,
#17 _CraigA_
Posted 04 September 2007 - 04:43 PM
I'll stick a photo up when I fit mine.
Cheers,
Craig.
#18
Posted 04 September 2007 - 05:05 PM
#19
Posted 18 December 2007 - 08:37 PM
a trace would be ideal. I would like to try to make one. Couldn't be too hard...
Grateful for any help....
#20 _lx5008_
Posted 19 December 2007 - 11:21 AM
OTHER PICS ARE ON MY PHOTOBUCKET SITE
CHEERS
#21 _lx5008_
Posted 19 December 2007 - 11:41 AM
#22
Posted 19 December 2007 - 11:41 AM
cheers
#23
Posted 19 December 2007 - 11:45 AM
diagrams...
Dimensions would be good but I can probably work it out with these pics.
Thanks for your help.
Dellas
#24 _73LJWhiteSL_
Posted 19 December 2007 - 12:26 PM
Steve
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users