Yep with the chrome dress trims they will look better, it will brake the black up between rim and tyres
Cheers john
Posted 31 October 2018 - 07:10 AM
Yep with the chrome dress trims they will look better, it will brake the black up between rim and tyres
Cheers john
Posted 31 October 2018 - 05:46 PM
I fited a t400 to my uc with pace maker headers. Had to trim the bell housing a little. I have posted pick,s of what I did.
http://www.gmh-toran...project-begins/
Darren
Posted 28 November 2018 - 09:34 PM
Posted 02 May 2019 - 08:12 PM
Posted 03 November 2019 - 09:48 PM
Posted 03 November 2019 - 09:50 PM
Posted 03 November 2019 - 09:59 PM
Posted 03 November 2019 - 10:04 PM
Posted 03 November 2019 - 10:28 PM
Posted 03 November 2019 - 10:30 PM
Posted 03 November 2019 - 10:46 PM
Posted 04 November 2019 - 09:13 AM
Pic of the finger for a before shot please.
You can cut yourself seriously on the wierdest things.
Lucky it wasnt at some of the workplaces Ive been on.
They would have made sure that there were safety covers on all fridge condensors by now.
Or thrown the exposed ones out and replaced them with covered types.
Cheers
Rob
Posted 04 November 2019 - 05:29 PM
Posted 28 November 2019 - 09:25 PM
Posted 29 November 2019 - 07:29 AM
Posted 29 November 2019 - 07:51 AM
Posted 30 November 2019 - 10:46 AM
Posted 01 December 2019 - 10:48 AM
Posted 01 December 2019 - 11:50 AM
Stick with it Mick - your making progress
Posted 01 December 2019 - 09:26 PM
Posted 03 December 2019 - 10:48 PM
Posted 04 December 2019 - 04:04 AM
How many times have you heard people winge about parts that don’t fit.
Well I’m gunna have my turn.
Aeroflow engine oil dipstick.
Oring set up on it sucks and coz I got the new extractors with the bigger primary’s, it’s kinda squished between the block and the extractors.
Flex plate cover
Not sure what brand it is.
But the bolt holes don’t line up.
ARP converter bolts are a poofteenth too big for the holes.
Think I’m gunna drill out the flex plate and converter.
It’s less than 1mm in it.
Bolts would go in if you were rough enough.
However more progress tonight.
Got the pipes bolted onto the heads just to test fit and check clearance.
I’ll get the grinder and an angle drill out to start modifying a few bits tomorrow.
Can’t find my damn starter motor bolts :(
Visit to rare spares on the cards tomorrow.
Posted 04 December 2019 - 09:29 AM
Hi Mick. Great progress. I'm wondering if you have your steering column in (I can't see from the photos) as I'm curious how you went/go with clearance. I'm at that point and having difficulty with the lower uni joint, and I have bought a Borgeson one to help. Cheers Ron
Posted 04 December 2019 - 09:09 PM
Hi Mick. Great progress. I'm wondering if you have your steering column in (I can't see from the photos) as I'm curious how you went/go with clearance. I'm at that point and having difficulty with the lower uni joint, and I have bought a Borgeson one to help. Cheers Ron
Posted 04 December 2019 - 09:28 PM
The trans dipstick I plan on drilling a couple holes through the lip on the firewall it seems to fit up nice at this point of time.I had same issues with gearbox and engine dipstick. Had to modify both. Had to drill flex plate out also.
0 members, 0 guests, 0 anonymous users